THOMAS4PARTS--FOR ALL YOUR TURBO & PERFORMANCE NEEDS--
Posted: Tue Dec 16, 2008 5:28 pm
Thomas4parts for all your performance needs.
We have been turbo charging and modifying Gemini's for over 20 years.
In the Top Ten street registered four cylinders in Australia 1991 to 1996
11.90 at 117 MPH in 1991 G180 TO4 DCOE WEBERNO NITROUS
11.46 at 112 MPH in 1996 G180 TO4 DCOE WEBER NO NITROUS
9.87 at 137 MPH 2007 4ZD1 NO NITROUS
7.17 at 179 MPH TWIN TURBO 13B ALTERED-- 36 PSI BOOST --(TUNED BY LEE)
--- Fastest 13B in the world to half track---
--- 1.01 60 ft times---
10.42 at 131mph 808 SERIES 6 13B 13 PSI BOOST
FOR SALE....
MLS Head Gaskets "G" and "Z"series...$260
MLS Turbo base Gaskets...From$16
MLS "G" & "Z" Exhaust Manifold Gaskets...$35 a set
MLS Gaskets to suit Turbonetics Deltagate or Tial 35mm or 38mm wastegates... $10 each
-------------------------------------------------------------------------------
Modified rodeo inlet manifold.
Plenum with cable mount to suit vn-vs T/body. We have taken all of the crap off the back of it and welded it all up so it looks smooth, lots of time goes into tidying them up. The fittings for the Map sensor, boost guage, wastgate and blow off valves can be tapped into the back or the under side...
$250
---------------------------------------------------------------------------------
Modified vn-vs T/bodies to fit 3 inch silicon pipe $75
------------------------------------------------------------------------------------
Double Row Timing Chain Gaskets--- COMING SOON --
-----------------------------------------------------------------------
MLS head gaskets now in stock. G161, G180,G200, 4ZC1, 4ZD1 and 4ZE1
$260 Plus postage.
G200 gasket setup to put the 1600cc head on------ In Stock--------
All of the "G" series gaskets are modified at the front of the head to accommodate double and single row timing chains, with the bolt holes slotted and the water gallery reduced for a good seal...
These gaskets have proven themselves in the hands of the fastest G180 powered gemini in the world (YEP9s 8.80 @152mph) and are a must for any high compression or boosted engines...
"G" series
"Z" series
They are 3 layer and are 1.4mm thick... $260
-------------------------------------------------------------------------------------
MLS "G" & "Z" Series Exhaust Manifold Gaskets...
"G"series
"Z" series
They are 5 layer with a flame ring... $35 a set
------------------------------------------------------------------------------------
MLS Gaskets to suit Turbonetics Deltagate or Tial 35mm or 38mm wastegates...
They are 2 layer with a flame ring... $10 each
------------------------------------------------------------------------------------
This is a couple of gaskets from our new MLS range
From the top Left clockwise, they are to suit...
TO4 Split Pulse-- $20
TV Flange--------- $20
TO4 Single entry- $18
T3----------------- $16
T04 Euro Flange- $18
T2----------------- $16
TA45-------------- $20
These Turbo gaskets are not single use gaskets like most of your normal turbo gaskets. These gaskets are good for a couple turbo changes and seal like no other....
------------------------------------------------------------------------------------
Trents Heavy duty torque tube rubbers
If your car shutters when accelerating or bangs in the mid section of your car when you are giving it a hard time, you more than likely need one of these.
$115 exchange (we need the feet for the new rubbers)
$125 posted anywhere in Australia
------------------------------------------------------------------------------------
New cushion donut rubber and new bearing
$135 exchange (we need the old one for the dust rings)
------------------------------------------------------------------------------------
Strengthened Torque Tube shafts $250 Balanced
------------------------------------------------------------------------------------
We can do complete Torque Tube assemblies as a bolt in deal...
#H/D shaft
#H/D rubber
#new donut assembly
#assembled ready to bolt in
we would need a complete exchange, and can be in a steel or alloy chasing, early or late... $550 Bolt in
------------------------------------------------------------------------------------
We are making up and selling a dizzy that is suited to run individual coils...
To suit "G" series... They will run with EMS, Microtech and Haltechs. $200
------------------------------------------------------------------------------------
4ZE1 dizzy cover for running it for a home signal and individual coils...
$140
------------------------------------------------------------------------------------
Spool conrods to suit "G" and "Z" series
G180, G200, 4ZB1, 4ZC1, 4ZD1 and 4ZE1
$550 a set
------------------------------------------------------------------------------------
Swivel feet valve clearance adjusters
$75 a set
------------------------------------------------------------------------------------
We sell all your valve trains needs...
#S/S valves in all sizes to suit G and Z series
#H/D valve springs
#Chromoly retainers and collets
PM me for a price
------------------------------------------------------------------------------------
Big bore fuel rail (17mm internal)
$30 for 400mm
We do custom fuel rails to suit your setup...
------------------------------------------------------------------------------------
We have a large range of silicon intercooler fittings, the wall thickness is 6 mm...
#reducing 90 deg bends 2 1/2inch to 3inch
#straight reducers ....... 2 1/2inch to 3inch
#straight hump joiners
#lots more
------------------------------------------------------------------------------------
"Z" series adjustable cam gear
Picture of the 4ZE1
$195
------------------------------------------------------------------------------------
Turbo manifold (Single Entry)to suit "G" or "Z" series
$550
------------------------------------------------------------------------------------
Chromoly Flex Plates for big power auto gemini's made from 3/16 plate and will handle any horsepower you put through it... $300
------------------------------------------------------------------------------------
Billet chromoly flywheel for "G" or "Z"
$500
------------------------------------------------------------------------------------
Custom forged piston to suit your setup
From $1000 a set
-----------------------------------------------------------------------------------
Now available... The Sprint 500 Haltech EFI computer...
Retail price $1090, we are doing a gemini terminated harness so we can do a good price on that any other parts and tuning...
Best way is to PM Lee at Thomas4parts on ozgemini for the best deal...
---------------------------------------------------------------------------------
We have been turbo charging and modifying Gemini's for over 20 years.
In the Top Ten street registered four cylinders in Australia 1991 to 1996
11.90 at 117 MPH in 1991 G180 TO4 DCOE WEBERNO NITROUS
11.46 at 112 MPH in 1996 G180 TO4 DCOE WEBER NO NITROUS
9.87 at 137 MPH 2007 4ZD1 NO NITROUS
7.17 at 179 MPH TWIN TURBO 13B ALTERED-- 36 PSI BOOST --(TUNED BY LEE)
--- Fastest 13B in the world to half track---
--- 1.01 60 ft times---
10.42 at 131mph 808 SERIES 6 13B 13 PSI BOOST
FOR SALE....
MLS Head Gaskets "G" and "Z"series...$260
MLS Turbo base Gaskets...From$16
MLS "G" & "Z" Exhaust Manifold Gaskets...$35 a set
MLS Gaskets to suit Turbonetics Deltagate or Tial 35mm or 38mm wastegates... $10 each
-------------------------------------------------------------------------------
Modified rodeo inlet manifold.
Plenum with cable mount to suit vn-vs T/body. We have taken all of the crap off the back of it and welded it all up so it looks smooth, lots of time goes into tidying them up. The fittings for the Map sensor, boost guage, wastgate and blow off valves can be tapped into the back or the under side...
$250
---------------------------------------------------------------------------------
Modified vn-vs T/bodies to fit 3 inch silicon pipe $75
------------------------------------------------------------------------------------
Double Row Timing Chain Gaskets--- COMING SOON --
-----------------------------------------------------------------------
MLS head gaskets now in stock. G161, G180,G200, 4ZC1, 4ZD1 and 4ZE1
$260 Plus postage.
G200 gasket setup to put the 1600cc head on------ In Stock--------
All of the "G" series gaskets are modified at the front of the head to accommodate double and single row timing chains, with the bolt holes slotted and the water gallery reduced for a good seal...
These gaskets have proven themselves in the hands of the fastest G180 powered gemini in the world (YEP9s 8.80 @152mph) and are a must for any high compression or boosted engines...
"G" series
"Z" series
They are 3 layer and are 1.4mm thick... $260
-------------------------------------------------------------------------------------
MLS "G" & "Z" Series Exhaust Manifold Gaskets...
"G"series
"Z" series
They are 5 layer with a flame ring... $35 a set
------------------------------------------------------------------------------------
MLS Gaskets to suit Turbonetics Deltagate or Tial 35mm or 38mm wastegates...
They are 2 layer with a flame ring... $10 each
------------------------------------------------------------------------------------
This is a couple of gaskets from our new MLS range
From the top Left clockwise, they are to suit...
TO4 Split Pulse-- $20
TV Flange--------- $20
TO4 Single entry- $18
T3----------------- $16
T04 Euro Flange- $18
T2----------------- $16
TA45-------------- $20
These Turbo gaskets are not single use gaskets like most of your normal turbo gaskets. These gaskets are good for a couple turbo changes and seal like no other....
------------------------------------------------------------------------------------
Trents Heavy duty torque tube rubbers
If your car shutters when accelerating or bangs in the mid section of your car when you are giving it a hard time, you more than likely need one of these.
$115 exchange (we need the feet for the new rubbers)
$125 posted anywhere in Australia
------------------------------------------------------------------------------------
New cushion donut rubber and new bearing
$135 exchange (we need the old one for the dust rings)
------------------------------------------------------------------------------------
Strengthened Torque Tube shafts $250 Balanced
------------------------------------------------------------------------------------
We can do complete Torque Tube assemblies as a bolt in deal...
#H/D shaft
#H/D rubber
#new donut assembly
#assembled ready to bolt in
we would need a complete exchange, and can be in a steel or alloy chasing, early or late... $550 Bolt in
------------------------------------------------------------------------------------
We are making up and selling a dizzy that is suited to run individual coils...
To suit "G" series... They will run with EMS, Microtech and Haltechs. $200
------------------------------------------------------------------------------------
4ZE1 dizzy cover for running it for a home signal and individual coils...
$140------------------------------------------------------------------------------------
Spool conrods to suit "G" and "Z" series
G180, G200, 4ZB1, 4ZC1, 4ZD1 and 4ZE1
$550 a set ------------------------------------------------------------------------------------
Swivel feet valve clearance adjusters
$75 a set------------------------------------------------------------------------------------
We sell all your valve trains needs...
#S/S valves in all sizes to suit G and Z series
#H/D valve springs
#Chromoly retainers and collets
PM me for a price
------------------------------------------------------------------------------------
Big bore fuel rail (17mm internal)
$30 for 400mmWe do custom fuel rails to suit your setup...
------------------------------------------------------------------------------------
We have a large range of silicon intercooler fittings, the wall thickness is 6 mm...
#reducing 90 deg bends 2 1/2inch to 3inch
#straight reducers ....... 2 1/2inch to 3inch
#straight hump joiners
#lots more
------------------------------------------------------------------------------------
"Z" series adjustable cam gear
Picture of the 4ZE1
$195------------------------------------------------------------------------------------
Turbo manifold (Single Entry)to suit "G" or "Z" series
$550------------------------------------------------------------------------------------
Chromoly Flex Plates for big power auto gemini's made from 3/16 plate and will handle any horsepower you put through it... $300
------------------------------------------------------------------------------------
Billet chromoly flywheel for "G" or "Z"
$500------------------------------------------------------------------------------------
Custom forged piston to suit your setup
From $1000 a set-----------------------------------------------------------------------------------
Now available... The Sprint 500 Haltech EFI computer...
Retail price $1090, we are doing a gemini terminated harness so we can do a good price on that any other parts and tuning...
Best way is to PM Lee at Thomas4parts on ozgemini for the best deal...
---------------------------------------------------------------------------------